Installationsmaterial Artikel 97 - 192 von 214 ⍾ ABB ⍾ Letzte Aktualisierung
Installationsmaterial ⍾ Seite 2
-
2TKA130002G1
The AK14 extension ring is used to change the depth of the AU8 and AU19 junction boxes, so that conduiting can take place above the concrete reinforcement. It gives a 75 mm space b …
-
-
-
2TKA130005G1
The AS12 strain-relief inlet is used in conduitless flush mounting to fasten 5 x 2,5 mm² cables to the mounting boxes or junction boxes. The boxes are installed in the standard way …
-
2TKA130008G1
The AS15 is designed to be used as a connector between AUS15.2 mounting boxes. Open needed knock-out holes on mounting boxes for the interconnector and install the boxes on the wal …
-
2TKA130009G1
The AS20 bushing insulator is used to attach conduit extensions, which have locking springs and a diameter of 20 mm, to a concrete casting mould. After the mould has been dismantle …
-
2TKA130010G1
The AS25 installation plug is used for fixing mounting/junction boxes through their base onto, for instance, concrete casting moulds. When the casts are removed, the plugs break at …
-
2TKA130015G1
Wall clamps offer a rapid means of attaching a mounting box to a 12-13 mm thick board wall. Wall clamp AS8.13 is available for 12 - 13 mm. The hole is made with an AT5 hole saw (Ø …
-
2TKA130020G1
The AUS15.2 mounting box is used in buildings that have board walls. The holes are made with a hole saw (AT1, or equivalent). After the required conduit or cable inlets have been k …
-
2TKA130026G1
The box AU17.2 has knock-outs for 11 inlets on the side, and 6 on the bottom. It can accommodate a device with a triple inlet. _x000D_If necessary, the box may be divided in two by …
-
2TKA130027G1
The AU19 junction box has knock-outs for 8 inlets and 4 bottom inlets. The box can be fastened using side nailing or a PMR577 support. The box has four screw pillars, two for M4 sc …
-
2TKA130029G1
The mounting box is designed for installation in all new buildings and in prefabricated building elements, and can be used with cast materials. It has a total of five knock-out inl …
-
2TKA130030G1
The device offers the AU3.2 mounting box modified with a 28 mm deep extension ring for use in walls built of bricks that have pipe ducts. No branch inlets are required at the botto …
-
2TKA130031G1
The characteristics of this box are the same as the AU3.2; the difference is in the inlets. The box has 2 branch inlets for D20 conduits. There are also 3 knock-out on the side, an …
-
2TKA130032G1
The box has 2 branch inlets with locking devices for D20 conduits. A separate inlet can be attached to the side opposite the fixed inlets. The bottom of the box has two inlets. Inl …
-
-
2TKA130038G1
A box is attached to its base from the inside with a PMR135 installation adaptor through the opened center blank. The screw-head is covered with the plug in the adaptor. The instal …
-
-
-
2TKA130042G1
The PMR399 is 60 mm deep and is often used in renovating old houses, when adding 50 mm thermal insulation to inside walls while leaving existing conduit installations in place. The …
-
-
2TKA130044G1
Low mounting boxes may be joined side by side by using a PMR474 interconnector, which must be cut to the height of the bottom of the box. Made of halogen free material (IEC/61249-2 …
-
2TKA130045G1
The PMR490 interconnector is used to link together mounting boxes when groups of installation boxes that house weak and strong current circuits are installed under different coverp …
-
2TKA130046G1
The connecting piece PMR502 is used when low-voltage or strong-current circuit box groups are installed under different cover plates. With connecting piece PMR502, the distance bet …
-
2TKA130047G1
Support PMR577 is used with mounting and junction boxes with knock-out inlets. The support is used for installation of boxes into light, non-bearing walls that are constructed on s …
-
-
-
2TKA140002G1
The square junction box AP10 (6,0 mm², 500 V) is equipped with 12 membrane cable entries (Ø 19 mm) in the sides, and two on the bottom. Cables are easy to connect by simply inserti …
-
2TKA140003G1
Die Anschluss-/Abzweigdosen von ABB sind aus einem Zweikomponenten-System gefertigt. Sie besitzen zehn seitliche leicht durchzustechende Membran-Kabeleinführungen und zwei weitere …
-
2TKA140004G1
The AP12 junction box has two 3-pole insulate 6 mm² connectors. The base plate offers a choice of eight different connection points for the connectors. In the bottom of the box the …
-
-
2TKA140006G1
The AP6 square junction box is spacious and easy to wire. The box is equipped with an insulated 5-way connector. The transparent wire connector makes it easy to ensure sufficient w …
-
2TKA140007G1
Square junction box AP6 is spacious and easy to wire. The box is equipped with an insulated 5-way connector. The transparent wire connector makes it easy to ensure sufficient wire …
-
2TKA140008G1
The round junction box AP7 (2,5 mm², 440 V) is similar to the AP9 and the AP10 and is equipped with 10 membrane cable entries (Ø 17 mm) and two in the bottom. Cables are easy to co …
-
2TKA140009G1
The round, dual-component connection box AP7.1 (2,5 mm², 440 V) is equipped with 10 membrane cable entries (17 mm) and two in the bottom. The cover of the box is equipped with thre …
-
-
2TKA140012G1
Die Anschluss-/Abzweigdosen von ABB sind aus einem Zweikomponenten-System gefertigt. Sie besitzen zehn seitliche leicht durchzustechende Membran-Kabeleinführungen und zwei weitere …
-
2TKA140013G1
Die Anschluss-/Abzweigdosen von ABB sind aus einem Zweikomponenten-System gefertigt. Sie besitzen zehn seitliche leicht durchzustechende Membran-Kabeleinführungen und zwei weitere …
-
2TKA140014G1
Die Anschluss-/Abzweigdosen von ABB sind aus einem Zweikomponenten-System gefertigt. Sie besitzen zehn seitliche leicht durchzustechende Membran-Kabeleinführungen und zwei weitere …
-
-
2TKA140016G1
The junction boxes AP7, AP9 and AP10 can be furnished with the strain-relief AS9 for Ø 6 - 19 mm cables. The strain-relief AS9 has a 5-pole connector (2,5 mm² ). The maximum wire c …
-
-
-
-
-
-
2TKA150003G1
The AK4 is a dual-component conversion cover (85 x 85 mm) for use in splash-proof and dry conditions. The screw distance is 60 mm. For cables Ø 6,0 - 15,0 mm. The cover is equipped …
-
-
-
-
-
-
-
-
-
-
-
-
2TKA160009G1
Die Rohrverbinder von ABB sind in der modernen Installationstechnik nicht wegzudenken. Durch einfaches Zusammenstecken zweier Rohre in die ABB Rohrverbinder werden diese unverlierb …
-
2TKA160010G1
Die Rohrverbinder von ABB sind in der modernen Installationstechnik nicht wegzudenken. Durch einfaches Zusammenstecken zweier Rohre in die ABB Rohrverbinder werden diese unverlierb …
-
2TKA160011G1
Die Rohrverbinder von ABB sind in der modernen Installationstechnik nicht wegzudenken. Durch einfaches Zusammenstecken zweier Rohre in die ABB Rohrverbinder werden diese unverlierb …
-
2TKA160012G1
Die Rohrverbinder von ABB sind in der modernen Installationstechnik nicht wegzudenken. Durch einfaches Zusammenstecken zweier Rohre in die ABB Rohrverbinder werden diese unverlierb …
-
2TKA160013G1
Die Rohrverbinder von ABB sind in der modernen Installationstechnik nicht wegzudenken. Durch einfaches Zusammenstecken zweier Rohre in die ABB Rohrverbinder werden diese unverlierb …
-
2TKA160014G1
Die Rohrverbinder von ABB sind in der modernen Installationstechnik nicht wegzudenken. Durch einfaches Zusammenstecken zweier Rohre in die ABB Rohrverbinder werden diese unverlierb …
-
2TKA160015G1
Die Rohrverbinder von ABB sind in der modernen Installationstechnik nicht wegzudenken. Durch einfaches Zusammenstecken zweier Rohre in die ABB Rohrverbinder werden diese unverlierb …
-
2TKA160016G1
A plug is supplied with each conduit end piece. Conduit end piece AJ5.16 is primarily used for termination of plastic conduits in concrete casting. After casting, the conduit end p …
-
2TKA160017G1
A plug is supplied with each conduit end piece. Conduit end piece AJ5.20 is primarily used for termination of plastic conduits in concrete casting. After casting, the conduit end p …
-
2TKA160018G1
Bushing insulator AJ9.16 is designed for feedthrough situations in electrical conduits in concrete structures cast on-site, and is used for linking conduits in the ceiling structur …
-
-
2TKA160020G1
The ANK20 angle inlet is equipped with locking device which prevents conduit disconnection. The conduit can be unfastened by twisting it. Angle inlet ANK20 is both right and left h …
-
2TKA160021G1
The back inlet is fitted with locking device. The conduit can be unfastened by twisting it. Inlet can be used both in mounting boxes and in junction boxes. Made of halogen free mat …
-
2TKA160022G1
The back inlet is fitted with locking device. The conduit can be unfastened by twisting it. Inlet can be used both in mounting boxes and in junction boxes. Made of halogen free mat …
-
2TKA160023G1
The back inlet is fitted with locking device. The conduit can be unfastened by twisting it. Inlet can be used both in mounting boxes and in junction boxes. Made of halogen free mat …
-
2TKA160024G1
Inlet AN16 is equipped with locking device which prevents conduit disconnection. The conduit can be unfastened by twisting it. The inlet can be used both in mounting boxes and in j …
-
2TKA160025G1
Inlet AN20 is equipped with locking device which prevents conduit disconnection. The conduit can be unfastened by twisting it. The inlet can be used both in mounting boxes and in j …
-
-
2TKA160027G1
Inlet AN25 is equipped with locking device which prevents conduit disconnection. The conduit can be unfastened by twisting it. The inlet can be used both in mounting boxes and in j …
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
